deedub35

All 20V max batteries work with all 20V max tools. Even the Flexvolt batteries work with all 20V max tools. So the 6AH batteries will work with the chainsaw. You can certainly buy them now, keep them sealed, and give as a Christmas gift. They will be fine. You will need to charge them before use of course.

Most of my work is bathroom renovations and basement developments. I have a DCS361 which I use for the trim work - casings and baseboards. I do the occasional deck here and there so then I use my DW718.

True and good point. But I’ve never had a 4x8 sheet of plywood, mdf, or even drywall be out of square. There’s always a framing square close by to check before cuts. You can hold a framing square against the anti splinter strips. After the first use of the tracksaw the edge of the strip IS where the left kerf of the saw blade is. The strip is straight and parallel to the metal track - just not the very end bits but that overhangs the material anyways.

I’ve had my tracksaw for quite some time and use it when cutting down sheet goods. Often it is expensive plywood or veneer for cabinet sides, backs, and shelves. So I can’t mess around with cuts being out. I’ve always used the dewalt clamps. Measure both ends of the piece, line up the track, clamp both ends, and cut. Way more accurate than relying on what looks like to be an 8” perpendicular piece of metal. Takes a minute more to set up the cut but I’m paid by the hour and having a cut out by 1/16 or worse is not an option.

The website still shows the DWS5028 miter gauge and DWS5027 T-square.

I would love a cordless pin nailer. I use one lots when doing cabinetry.

No tools required. Twist the knob counterclockwise to remove the black housing. Twist the tensioning knob to give enough slack. Done - 10 seconds give or take. I take it apart after every use to clean out the accumulated debris. I found out that if you don’t the bar/chain oil wicks out and you end up having a mess on the floor of your work van or counter.

Maybe I will. Warranty has long since elapsed.

Say hello to my lil friend. Made my deck demo go a lot easier.

No. It’s pretty basic - press the button, wait for it to self calibrate, and then it should start spinning. That’s what it used to do. I’m sure it’s something internal. I’ll see what the service repair says. Last week I had the unit screwed to the ledger board and I had to manually aim the laser dot towards the footings so I could get the post height. I only had 3 posts but I was by myself and it was annoying going back and forth to get this laser dot to hit the grade rod. My colleague who is a home builder is going to lend me his for my next deck build in two weeks. I’m not going to buy another one because I don’t use it much at all. I only do one or two decks a year - I’m more into bathrooms and kitchens. With that said if the repair cost is too much I’ll just bin this POS.

I have had this laser level for a while now. I haven’t used in a bit though. Brought it out this week as I was starting a deck build. Everything powers up and lights up but the head doesn’t spin. Any similar experiences, suggestions, or solutions? If not a trip to the service center I guess. Might not even be worth fixing?

Here is some pricing from a KMS Tools - a chain of tool stores in Western Canada.

So this post is not to show off my work but to show the precision of the saw in case there are some on the fence about picking one up. First off I installed the base, shower faucet, mould/moisture resistant wallboard, and then the Kerdi waterproofing. Then I installed the 12x24 porcelain tiles in a horizontal grid pattern. The top row of tiles needed to be ripped a bit leaving slivers. What I found impressive was that the slivers (1/8" to 1/4" wide) remained intact! That is precision!

60 mil vinyl decking - brand names include Duradek, Tuffdeck, etc.

Not sure why you would want to have the whole assembly bolted together. Have you considered the cleaning aspect? I do a lot of tiling. At the end of the day there is a lot of tile residue at the bottom of the tray. For me clean up always involves taking the table off and bringing all the components outside for a hose down.