BababooeyHTJ Posted April 4, 2017 Report Share Posted April 4, 2017 20 minutes ago, SetBuilder said: I only use 2 amp red lithium batteries on my impacts to save weight. I have 4, 5 amp but I use them for circular saw, drills, sawzall etc. I only had one instance where the power cut out but like I said, it was a large bolt. What size screws are you driving when it happens? My 2757 has more power, but I rarely use it since buying the Surge. Im my work I'm mainly driving 1 3/4 to 3 in drywall screws. Not too sure what it was. Probably a long #10 into a 4x4. Was playing around with it when I got it. Although yesterday I tried it with a 3/8 lag into a lead concrete sleeve. That was a no go. Power cut out right away. Wasn't expecting to be up to the task. The first gen fuel didn't skip a beat. I'm just not a fan of how it just cuts off power instead of limiting current. In more realistic usage where it would work just slowly it'll cut out. I do love how it works with smaller fasteners and doesn't trash bits. Just thrown off by the torque limit. If it were just underpowered that would be one thing but this will just stop doing the job. If I didn't know and didn't have my impact driver with me I would be pissed. It is great for the vast majority of what I do. Just has one large downfall. Quote Link to comment Share on other sites More sharing options...
SetBuilder Posted April 5, 2017 Author Report Share Posted April 5, 2017 Today we were putting together a bunch if steel deck so I used the one key impact instead of the surge. Mainly because if I had to loosen a bolt put on by my co workers Makita or Dewalt I know the Surge is not up for the task. Quote Link to comment Share on other sites More sharing options...
Biggie Posted April 6, 2017 Report Share Posted April 6, 2017 Looks to me like you need a impact wrench. 2 Quote Link to comment Share on other sites More sharing options...
KnarlyCarl Posted April 6, 2017 Report Share Posted April 6, 2017 13 hours ago, Biggie said: Looks to me like you need a impact wrench. Yeeeaaaahh when your socket starts making the impact driver look small you know you need a impact wrench 1 Quote Link to comment Share on other sites More sharing options...
Bremon Posted April 6, 2017 Report Share Posted April 6, 2017 Lol! That's hilarious. Quote Link to comment Share on other sites More sharing options...
M1Deuce Posted July 13, 2017 Report Share Posted July 13, 2017 On 3/19/2017 at 6:45 PM, Biggie said: I don't see how there wouldn't be a market for a m12 surge. I would think this market doesn't need high torque or high production, if they did they would probably be running a 18v of some type. But a lot of these people are working indoors (maintenance, plumber, punch list) and in small areas such as cabinets running mostly small fasters. As far as I'm concerned those are places the low noise level of the surge are really going to shine. I've been all about the m12 tools for the past 4 years, the compact batteries are what I liked the most. They allow you fit in tight spaces. Recently picked up the surge with the "compact" m18 batteries and it is my go to impact, but the only complaint is the how large the m18 batteries are. I'd love an m12 verision. But I think we need someone to make an actual compact battery for the m18 line. Something like the Makita 12v battery. It would save almost an inch which would be very helpful. I know using longer bits help, but I think shorter is always better. 2 Quote Link to comment Share on other sites More sharing options...
Bremon Posted July 14, 2017 Report Share Posted July 14, 2017 @M1Deuce how would you propose that? The Makita uses 3 18650 sized lithium ion cells for 10.8v nominal voltage. The M18 is 66% larger just based on the fact it uses 5 18650 cells. The M12 puts those same 3 cells as the Makita in the grip of the tool, leading to no base under the handle but a fat grip. The Surge is a fairly weak tool (realistically specialized might be a better description) so either power suffers or runtime suffers tremendously; the housing and mechanism of the tool remain the same size but the handle changes slightly. I don't suspect there is a large market for that tool but maybe 2018 will show otherwise. Quote Link to comment Share on other sites More sharing options...
BK13 Posted July 17, 2017 Report Share Posted July 17, 2017 So I read somewhere about one of the other fluid impacts not really being good for building a deck. Would those who have one would you consider the M18 appropriate for deck building? Quote Link to comment Share on other sites More sharing options...
SetBuilder Posted July 17, 2017 Author Report Share Posted July 17, 2017 I mainly use my surge for 1 1/4 to 3in dry wall screws. I also have a Fuel 1/4 impact and a 1st gen impact. I would hate to stir you wrong, so I would check with the manufacturer. Quote Link to comment Share on other sites More sharing options...
FrosBros82 Posted July 17, 2017 Report Share Posted July 17, 2017 8 hours ago, BK13 said: So I read somewhere about one of the other fluid impacts not really being good for building a deck. Would those who have one would you consider the M18 appropriate for deck building? I have built two different decks using the M18 fuel. One the first generation, the second being the one-key. I didn't have a problem with either one, as they both drove screws just fine for me. Quote Link to comment Share on other sites More sharing options...
khariV Posted July 17, 2017 Report Share Posted July 17, 2017 12 hours ago, BK13 said: So I read somewhere about one of the other fluid impacts not really being good for building a deck. Would those who have one would you consider the M18 appropriate for deck building? Perhaps that might be from the Ridgid's tendency to vibrate pretty heavily when under strain driving long lags. Putting in decking screws shouldn't be any challenge at all for it. Just last summer, I built a deck using my M12 Fuel impact driver for everything but the 6"lags. 1 Quote Link to comment Share on other sites More sharing options...
SetBuilder Posted July 17, 2017 Author Report Share Posted July 17, 2017 One guy I was working with said his Makita Soft impact broke while putting in lags building a deck. Quote Link to comment Share on other sites More sharing options...
BK13 Posted July 17, 2017 Report Share Posted July 17, 2017 7 hours ago, FrosBros82 said: I have built two different decks using the M18 fuel. One the first generation, the second being the one-key. I didn't have a problem with either one, as they both drove screws just fine for me. The Surge? Quote Link to comment Share on other sites More sharing options...
FrosBros82 Posted July 17, 2017 Report Share Posted July 17, 2017 @BK13 No, just normal. My apologies, I didn't read your prior post about what model for Milwaukee you were exactly talking about. I have no skin in this, as I don't own a surge. FB82 Quote Link to comment Share on other sites More sharing options...
BK13 Posted July 17, 2017 Report Share Posted July 17, 2017 No sweat, you mentioned Gen1 and Gen2 and figured you were talking about the normal impact driver. Quote Link to comment Share on other sites More sharing options...
SetBuilder Posted February 18, 2018 Author Report Share Posted February 18, 2018 Well a little over a year of use and I just filled out all the E Service info to send my Surge back. It lost power and drives screws super slow. Maybe it just needs an oil change Ha ha ha.... 1 Quote Link to comment Share on other sites More sharing options...
Biggie Posted February 18, 2018 Report Share Posted February 18, 2018 Is it a motor issue or a impacting mechanism issue? Quote Link to comment Share on other sites More sharing options...
SetBuilder Posted February 18, 2018 Author Report Share Posted February 18, 2018 I think its something in the electronics, I was able to get it working normal switching back and forth between forward and reverse a few times, but then it crapped out again. Switching torque settings had no change in getting power back to normal. Quote Link to comment Share on other sites More sharing options...
The.Handyman Posted February 18, 2018 Report Share Posted February 18, 2018 I think its something in the electronics, I was able to get it working normal switching back and forth between forward and reverse a few times, but then it crapped out again. Switching torque settings had no change in getting power back to normal.There is a life span of the oil inside. I've heard of people heating up the fluid from heavy use and losing impacting strength. Quote Link to comment Share on other sites More sharing options...
SetBuilder Posted February 18, 2018 Author Report Share Posted February 18, 2018 I don't think thats it, I was not using it much at all today when it crapped out. after some messing with it it worked fine for a while then crapped out again. If the oil was passed its life span then it would have not worked again... No? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.