wingless Posted March 8, 2019 Report Share Posted March 8, 2019 A long time ago I had a really nice Craftsman Professional 315.17380 router, 14701 case, 9-25444 router table, 9-25179 edge guide and bits that suffered from a long period of inactivity, so they were sold. There are upcoming projects that require these tools, so replacements were sought and obtained. It turned out that I ended up w/ two routers, because both were good deals, one with two nice bit sets, the other with the 9-25179 edge guide. I also got a 9-25173 edge guide. Both routers have the nice Craftsman 9-1472 black Permanex polyethylene plastic cases. A router table was purchased separately and is detailed in this topic. One tool is the Craftsman 315.17381 router. This has the micrometer dial style depth adjustment. This also has a pair of base holes for a rod-style 9-25173 edge guide. When I obtained this router, the bare aluminum base casting had black marks, like large black greasy fingerprints, that could not be removed. I tried steel wool soap pads to polish the bare aluminum, but those marks remained. Those marks were removed and the castings restored to a new finish w/ fine grit random orbital motion sanding. This tool has a nice setup adjustment mechanism. There is a block w/ set screws that eliminate the play / slop between the base and motor, once properly adjusted. The result is a nice up / down movement w/ little / no displacement when locking the setting. The other tool is the Craftsman 315.17560 1¼ hp router. This has a large rotating ring, around the entire tool circumference to set the depth adjustment. Note that this adjustment style works best in normal orientation, w/ the base on the bottom, motor on top. If the tool is hung upside down, such as in a rotor table, this adjustment ring doesn't work as-intended. This tool also has a bright integrated internal light to illuminate the cutting bit. One bit set is the Craftsman 9-21297 18-piece Kromedge high speed steel router bit set. This has a nice case w/ plenty of room for additional bits of different styles and sizes. The flexing plastic hinge on my case failed, so I wrapped the back surface w/ 2" wide heavy duty Velcro and that became my hinge. The other bit set is the Mastergrip 480083 18-piece carbide tip router bit set. This has a nice metal-hinge / metal-latch birch wood case, w/ felt lining, foam padding and nylon shaft retention sleeves. The bits w/ guides all have nice ball bearing guides. The Craftsman 9-25179 edge guide is a great accessory. The existing router base is removed / replaced with the one from this accessory. The tool can be used w/ this base installed, with or without using the detachable edge guide part. This accessory permits accurate: edge; contour; trim; bevel and full circle cuts. The Craftsman 9-25173 edge guide is well-designed and integrates nicely with the Craftsman 315.17381 router. The two guide rods fit into existing casting holes in the router. The guide has a really nice fine-tune adjustment knob. This tool has both a straight edge guide and a contour finger guide. The Craftsman 9-1472 black plastic cases provide great tool storage, have a location for the 9-25119 edge guide and hold 14 router bits w/ ¼" shanks. Craftsman 315.17381 Router - Craftsman 9-1472 Permanex Polyethylene Case - Craftsman 9-25179 Edge Guide Craftsman 315.17381 Router - Craftsman 9-25173 Edge Guide Craftsman 315.17381 Router Base Polished Front Craftsman 315.17381 Router Base Polished Rear Craftsman 9-1472 Permanex Polyethylene Case Craftsman 9-1472 Permanex Polyethylene Case - Craftsman 9-25179 Edge Guide Craftsman 315.17381 Router - Craftsman 9-1472 Permanex Polyethylene Case - Craftsman 9-25179 Edge Guide Craftsman 315.17560 1¼ hp Router - Craftsman 9-1472 Permanex Polyethylene Case Craftsman 315.17560 1¼ hp Router - Craftsman 9-1472 Permanex Polyethylene Case Craftsman 9-21297 Bit Set Mastergrip 480083 Bit Set Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.