engiab Posted June 25, 2017 Report Share Posted June 25, 2017 Hi Guys. I have a Makita xph01 and a Lxph03. I replaced the carbon brushes for xph01 and works good but I replaced the carbon brushes on Lxph03 and when I pressed the trigger it try to start and makes a spark and won't start again. Do you know what happen and what I must do to fix it. I will appreciate the help. 1 Quote Link to comment Share on other sites More sharing options...
kornomaniac Posted June 26, 2017 Report Share Posted June 26, 2017 Burnt up the motor ? 2 Quote Link to comment Share on other sites More sharing options...
engiab Posted June 26, 2017 Author Report Share Posted June 26, 2017 hi kornomaniac, there any test for the motor, to know if it is working or not? Quote Link to comment Share on other sites More sharing options...
HiltiWpg Posted June 26, 2017 Report Share Posted June 26, 2017 You can quickly meter it for a short in the windings.Sent from my Pixel using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
CATERPILLAR Posted June 26, 2017 Report Share Posted June 26, 2017 20 hours ago, engiab said: Hi Guys. I have a Makita xph01 and a Lxph03. I replaced the carbon brushes for xph01 and works good but I replaced the carbon brushes on Lxph03 and when I pressed the trigger it try to start and makes a spark and won't start again. Do you know what happen and what I must do to fix it. I will appreciate the help. Possible Burnt up armature it is common. Can U send a picture of what it looks Like ? 2 Quote Link to comment Share on other sites More sharing options...
engiab Posted June 26, 2017 Author Report Share Posted June 26, 2017 yes, Caterpillar, I will send it later this afternoon, I must open the drill and I out of the house. Thanks. 1 Quote Link to comment Share on other sites More sharing options...
engiab Posted June 26, 2017 Author Report Share Posted June 26, 2017 HiltWpg, thanks for your answer, I will do it later, I'm out of the house and I will let u know. Quote Link to comment Share on other sites More sharing options...
engiab Posted June 27, 2017 Author Report Share Posted June 27, 2017 13 hours ago, HiltiWpg said: You can quickly meter it for a short in the windings. Sent from my Pixel using Tapatalk Hi HiltiWpg, I did the test for armadure, testing the windings and the ohms reading 180 degree was 0.05 ohms in everyone. What I must do next... thanks Quote Link to comment Share on other sites More sharing options...
CATERPILLAR Posted June 27, 2017 Report Share Posted June 27, 2017 11 hours ago, engiab said: Hi HiltiWpg, I did the test for armadure, testing the windings and the ohms reading 180 degree was 0.05 ohms in everyone. What I must do next... thanks New armature I would say . if do u mean 180 degrees f ? 1 Quote Link to comment Share on other sites More sharing options...
HiltiWpg Posted June 27, 2017 Report Share Posted June 27, 2017 Try this, it may help. Sent from my Pixel using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
engiab Posted June 28, 2017 Author Report Share Posted June 28, 2017 Thanks HiltiWpg. Yes, I used this video to do the test and gave me 0.05 ohm between each opposite position(180 degree) windings. Following the instructions look like my armature is good (it is not in short). 1 Quote Link to comment Share on other sites More sharing options...
engiab Posted June 28, 2017 Author Report Share Posted June 28, 2017 Hi Caterpillar, I found the makita armature replacement price, It is cheap. I will by one and let u know. Thanks. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.