[Dewalt DW321 Help please...]

That would likely be the lever for changing the blade.
 

 

https://www.manualslib.com/manual/39489/Dewalt-Dw321.html

 

 

 

[My bits are dropping off :(]

It sounds to me like you are inserting the driver tip directly into the drill. You will need to use the silver 1/4” driver in the drill first. It has a notch at the end designed to lock into the impact. Then the tip goes into the driver and that should be held in with either a magnet or a wire ring inside the silver driver. 

[DWS779 and DWS780 Blade Tool Storage]

Behind the fence on the right side. It’s a spring type clap the aren’t will snap in to.


Sent from my iPhone using Tapatalk

[No 10" sliding miter for DeWalt?]

That one on Amazon is unavailable.

did you click the link? It let me add it to my cart.


Sent from my iPhone using Tapatalk

[No 10" sliding miter for DeWalt?]

https://www.amazon.com/DEWALT-DW717-Double-Bevel-Sliding-Compound/dp/B001AIX5OO/ref=mp_s_a_1_4?dchild=1&keywords=dw717+dewalt+miter+saw&qid=1585142997&sr=8-4

[Dewalt Dw871 Replacement Motor]

Just buy a new saw. It’s not much more than what a new motor would likely cost you. 
 

https://www.toolsid.com/dewalt/14-abrasive-chop-saw-electric-mpn-d28710.html?view=042084&utm_source=microsoft&utm_medium=cpc&utm_campaign=268680567&utm_content=1173179535357969

[40V OPE discontinued?]

I just Went into a service center to have my 40v blower repaired and they’re are switching around some model numbers and changing some things. They had a hard time ordering a replacement due to this. 

 

https://www.dewalt.com/products/power-tools/shop-by-cordless-platform/40v

[Dewalt power station]

Lots of sites have it in stock. Looks like the option with batteries is discontinued though.

https://www.dewalt.com/products/gear-and-equipment/generators-and-portable-power/1800-watt-portable-power-station-and-simultaneous-battery-charger/dcb1800b

[Flexvolt 6 and 9 Ah on the 20v mitre saw ?]

ah ratings only add negligible amounts of “power.” The key factor is runtime. 6 vs 9, you should see roughly a 50% linger runtime.

[Plunge/ track saw 102" / 2.6m rail]

I’ll give you that it’s a hair too short but I rip 8’ sheets regularly. There’s a finite amount of wiggle room to set the track on a 8’ rip for it to work properly. Takes a few minutes to figure out but once you do, mark your track so it’s easily setup next time.

[Fiber Cement on the Miter Saw?]

is fiber cement another name for hardiboard? The guys at work claim hardi does a bad job with high wind.

Fiber Cement is the generic name. Hardie is a brand name. CertainTeed also makes Fiber Cement siding as do many other manufacturers.

[Fiber Cement on the Miter Saw?]

Dewalt makes fiber cement shears. dustless.

[DeWalt plastic material, What is it?]

Depends on the tool and generation. Nylon PA6 and Polycarbonate & PBT.

[Found a flexvolt miter saw for $100]

Depends on how close the nearest DEWALT Service Centre is from your home. If it was in my area, I’d buy it.

[OSB + Paint]

What is the best way to Paint OSB so that the wood texture doesn't show? Would coat of oil based primer then a skim coat be best?

Best way would be to get some 1/4 ply to sheet over the OSB with.

[Chuck/jaws spinning after releasing trigger on DCD791?]

I'm pretty sure all my drill/drivers do if they aren't clamped down on a drill bit or driver.

[2x20V lawn mower]

20v?!?! Where's the 40v?

[Random screenshots for discussion]

[Random screenshots for discussion]

[Flexvolt Mud mixer]

what is expected availability in stores ?

Not sure. The units at the event don't even have branding on them yet. Probably just final prototype/proof of concept. May be a while.

[DeWalt Yeti/Arctic competition]

Looks cute (assuming they aren't giant boots!)

They have varying sizes. Looks like it's up to 65 qts.

[DeWalt Telescopic light]

 

[DeWalt Metal Snips]

 

 

[DeWalt Yeti/Arctic competition]

[Flexvolt Mud mixer]