Jump to content

Craigh9916

Members
  • Content count

    416
  • Joined

  • Last visited

Community Reputation

212 Excellent

About Craigh9916

  • Rank
    Senior Member

Background

  • Favorite Tool or Brand
    Impact driver

Recent Profile Visitors

1,244 profile views
  1. What tools did you buy today?

    Porter cable in the uk is Stanley fatmax and it’s total crap Sent from my iPhone using Tapatalk
  2. Found a good trick to use a laser level outside !

    I have the green glasses but I meant this trick is for when you just can’t see it at all in sun light at a distance Sent from my iPhone using Tapatalk
  3. DeWalt equivilant to Milwaukee ECX #1 #2 bits

    Does the bit holder in the set have a snap ring inside or is it just the magnet holding the bit in ? Sent from my iPhone using Tapatalk
  4. M12 gen 2!

    Yes I’ve just bought the Gen 2 impact and I’m so impressed with it , the speed settings work really well and the self drilling mode is good for small screws into timber as it backs off the power when it seats the screw works great ! I’ve got the 6 Ah batteries in the kit and the impact is just a really nice balance with them. The thing I’m most impressed with is the power and speed for a 12v I think it shames most 18v impacts Sent from my iPhone using Tapatalk
  5. What tools did you buy today?

    I take it you have the gen 2 drill driver then ? What’s that like do you rate it ? Sent from my iPhone using Tapatalk
  6. What tools did you buy today?

    Do they not do them where your from then ? I would have preferred the other hard case the red one that is moulded with the metal clips . Really impressed with the impact , did a side by side test with my dewalt dcf887 which was on a 2ah battery and had both in speed 3 using 70mm wood screws in to timber and the m12 was faster I couldn’t believe it ! Sent from my iPhone using Tapatalk
  7. What tools did you buy today?

    treated my self [emoji51] Sent from my iPhone using Tapatalk
  8. Issues with PS22 12V hex driver

    It was the multitool damaging the batteries , the 1.3 Ah batteries are fine I have plenty and never had one fail ! On the bosch forum the largest thread is the one about the batteries failing and all the response points to the multitool damaging them Sent from my iPhone using Tapatalk
  9. Issues with PS22 12V hex driver

    Yes keep an eye out for that and see if it does that , also try swapping the battery like I said as that used to get mine going again Sent from my iPhone using Tapatalk
  10. Issues with PS22 12V hex driver

    I used to get the exact same thing with my bosch gdx -vec it would all of a sudden do exactly what you have described but if I put it down and left it for 1 minute it would start again ! Also I sold that and bought the gdr-vec which did exactly the same and what it was is the tools electronics was kicking in the circuit protection and just getting a bit confused and then sorting its self out but this only happens on brushless bosch tools and with mine there was a trick to get it going take the battery off and put another on and the drill starts working again and then I put the original battery back on and it works fine still. By the way I did notice it only happened when the battery dropped a light on the fuel gauge ! And it wasn’t a battery issue as I sold my gdx to my friend and the problem continued with him too using his batteries! Sent from my iPhone using Tapatalk
  11. Dewalt dce089g

    I’m not familiar with that laser but normally that will be either it’s in the lock position so it’s reminding you it’s not a level line or the battery is low or the ground is to far out of level for the pendulum to find it’s own level but like I said I don’t know the laser that you have just check these things ! Sent from my iPhone using Tapatalk
  12. Has anyone got the dcf888 yet ?

    Yes I agree with everything you have said but I find after the delay when the impacts kick in they aren’t delicate at all. I will buy the dcf888 when I find one at a decent price Sent from my iPhone using Tapatalk
  13. Has anyone got the dcf888 yet ?

    I love my 887 but the speed one is just crap , I had the bosch gdx and speed one was very good Sent from my iPhone using Tapatalk
  14. Has anyone got the dcf888 yet ?

    Yes I know it’s deliberate but it’s also shit ! Sent from my iPhone using Tapatalk
  15. Has anyone got the dcf888 yet ?

    So you can get rid of the horrible delay the dcf887 has in number one setting ? Thanks Sent from my iPhone using Tapatalk
×