Stercorarius Posted March 1, 2016 Author Report Share Posted March 1, 2016 Inside Her Drawers Started From the Bottom... Channellock Snap-Ring-Pliers: These run about $20 and come with interchangeable tips. They toggle between internal and external retaining rings with a lever. Way better than some of the garbage I have used. Just like all the other blue handled tools, Channellock really knew what they were doing with this piece. Case External Snap Rings: These were $17. They're for retaining rings on backhoes and stuff. They are usually used on PTO adapters on tractors. 88 cent Project Source Screwdrivers: Great small pry-bars Kobalt Needle Nose Pliers: These came in the $40 set and are the most impressive of them. I use them all the time for pulling cotter pins. Gearwrench Ratcheting Hose Clamp: These are used to clamp down on radiator or other hoses to keep fluids from spilling out when you pull them. Haven't seen much use yet. No Name Slip Joint Pliers: Picked these up off the ground somewhere because I hate tools being thrown away. They work. Middle: Performance Tool Thumb Ratchets: The whole set was $11 on Jegs so I couldn't resist. They only see occasional use, but I like them. Pittsburgh Flare End Crowsfeet: This whole set was like $8 but I wouldn't recommend them to you. After one nut I had one get what almost looks like heat discoloration. It has faded now but it really had the full rainbow effect before. Powerbuilt Pickle Fork: For separating ball joints. It was cheap and seems alright. Lisle Helping Hands: I bought these from Summit Racing for about $12 and love them for automotive soldering. Each part is independent and magnetic (not weak magnets either) so you can throw them on any surface of your vehicle or leave it floating on the wire. Makes rewiring a car a lot easier. Bostitch Punch Set: Not a big Bostitch fan. The smallest one broke pretty quickly. I know that was my fault though. I will probably replace these with a sunex set. Evercraft Flare Nut Crowsfoot Set (MM): These are a step above the Pittsburghs but are not Ideal. ... Now We're Here Pittsburgh Extra Long Wrenches: Part of the same set in a prior episode. Seriously, if anyone knows of a name-brand wrench that is this long, let me know. Craftsman Ratcheting Box End Wrenches: These were about $30 so I can't really complain about them. Craftsman isn't the name it used to be. The only noticeable difference between this and the Pittsburghs I have used is the fact that they are made in the U.S.A. I might pick up a set of the Pittsburghs in metric because they are less than $10 and are similar quality. Husky All-Socket Tool: It was on sale over the holidays so I bought one. It sees rare use but it functions well for holding nuts in a tight spot while you try to get a bolt threaded on. Mix of Adaptors: Always seem to need a 1/2 to 3/8 and can never find one. I would like to get some higher quality ones. Mixture of Extensions: There are Crescent's, Stanley's, and Pittsburghs in here. I don't trust the chrome on the Pittsburghs. It is just a matter of time before it flakes. Then I will have an excuse to get some slightly nicer ones. I will go over the other toolbox tonight. Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 1, 2016 Author Report Share Posted March 1, 2016 For the record...ID love to be inside her drawers. [emoji14] I have a digital caliper from HF and I like it. How do you read an analog? Only my extension gets to go inside her drawers. Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 2, 2016 Author Report Share Posted March 2, 2016 Episode 9: Socket To Me Part 2 Time for the second box. Top Compartment: Proto Flare Nut Wrenches: These were about $100 for the set of three standards and about $120 for the set of five metrics. I love these American made wrenches and don't regret purchasing them. The one thing that I will say though is that if you are in the market for a set of flare nut wrenches, just buy yourself something cheaper. I would have just grabbed the sunex set that included all of these wrenches and would have only ran maybe $60 Leatherman bits HF Flashlight: Already covered Inkzall: I'm not a marker expert or snob. 3-in-1 Oil: I've been lubricating a lot of the moving parts on my tools with this because It comes in a convenient bottle and lasts forever. Stanley Classic 99 Utility Knife: Not as convenient as newer auto change knives, but you can't argued with the time tested and proved tool or price. OEM Tool O2 Sensor Socket and Axle Nut Socket: Both of these are for hondas. I'm not the biggest fan of OEM tool but these get the job done. Pittsburgh T-Handle Metric Allen Keys: I bought these because I love this format of Allen wrenches and they were $6. The handles are made out of garbage plastic and the steel is pretty soft. Proto Fractional T-Handle Allen Key Set: These are on the opposite end of the tool spectrum. They come in costing $125 list and were purchased for $88. I love these guys, but I have to say that the clear plastic case deal they came in was complete garbage, hence one of those awesome Milwaukee document bags. What's in the Box? These drawers are full of sockets. There is a drawer for each drive size. I will start at the bottom drawer with the 1/4 drive sockets so you have a better idea of why I bought so many Pittsburgh Sockets. Pittsburgh Deep Well Sockets SAE and Metric: These are all in a chrome finish. I wouldn't recommend them to professionals as the chrome will eventually chip. Pittsburgh Colored Shallow Sockets: I will talk about these sockets when I get to the 3/8 Assorted Crescent Sockets: Decent sockets that have handled substantial abuse without chipping. All of these socket sets can be had for about $10-$15 a piece. The metal rails they are on are 88 cent Pittsburgh socket rails that I am really impressed with. The rails were all cut to length using bolt cutters. The double sided plastic rail is actually a Kobalt that I am really impressed with. My only issue with these Kobalt socket rails is that they run almost $20. Proto MM 12 Point Socket Set: Hands down the best sockets I own. They are also the reason I have so many Pittsburghs. The Pittsburghs run about $10 for a set like this. This set of 1/4 drive protos cost me..... $90. I found out the price when I brought them to the counter and bought them because I don't like backing out at that point. It also caused me to go out and buy all the Pittsburghs that I have. I can't afford to buy all the sockets that I need in Proto at once, but for the price of one Proto set I was able to fill all my drawers with Pittsburgh sockets. The Pittsburgh sockets will be replaced eventually with higher end sockets, but not until I destroy them. 3/8 Drawer Assorted Pittsburgh and Crescent Sockets Pittsburgh Colored Sockets: I bought these sorta experimentally to see if it would really help me find my sockets. I have to say that it really doesn't. If you look closely the finish comes off almost immediately and it seems like the chrome on these chips faster than the plain chrome Pittsburgh sockets. If you are going Pittsburgh I would probably avoid these. Lisle Hex Key Sockets: I'm a big Lisle fan just because of how many innovative products they have. While these aren't new or innovative, they do work. 1/2 Drawer: This is the area of sockets that could really use improvement. I want to get some 12 point sockets and some shallow sockets in 1/2 and also some 12 points in 3/8. 2 Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 2, 2016 Author Report Share Posted March 2, 2016 I know none of you are wondering but the HD under the Husky is a reference to this video at somewhere between 3:45 and 4:00. I have to throw out a warning that this video contains some strong and potentially offensive language. I think you'll probably like it Protoolnut. 2 Quote Link to comment Share on other sites More sharing options...
T75R Posted March 2, 2016 Report Share Posted March 2, 2016 Lol that video is pretty funny Quote Link to comment Share on other sites More sharing options...
JimboS1ice Posted March 2, 2016 Report Share Posted March 2, 2016 Those must be some heavy boxes dude I know you said you wanted small ones for mobility but there's a lot of weight in there. Jimbo Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 2, 2016 Author Report Share Posted March 2, 2016 Those must be some heavy boxes dude I know you said you wanted small ones for mobility but there's a lot of weight in there. Jimbo Sent from my iPhone using Tapatalk They are rated for not that much. As far as current weight, I'd estimate 60lbs. Quote Link to comment Share on other sites More sharing options...
JimboS1ice Posted March 2, 2016 Report Share Posted March 2, 2016 They are rated for not that much. As far as current weight, I'd estimate 60lbs. That's not too bad actually Jimbo Sent from my iPad using Tapatalk Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 2, 2016 Author Report Share Posted March 2, 2016 Episode 10: The Chest Is The Best Today I've got my Husky rolling tool Chest. This is the same one the guys have in most of their videos. http://They really knew what they were doing when they named it one of the best of the best of 2015. This thing is cheaper, well I should say costs less than anything you can find at Harbor Freight, but it is an extremely nice toolbox. Exterior: Irwin Vise: About $880. I can't comment on longevity, but first impressions are overall positive. Misc Magnetic Trays: I can't get enough of these. They're cheap and great for holding interior trim screws and razor blade pieces. Top Drawer Proto Torque Wrenches: I have a 3/8 that gets me up to 80 ft/lbs and a 1/2 that gets me up to 250 ft/lbs. I purchased these when I was 15 and 16 to put my motor together. I don't remember what the price on these was, but I do remember that the shop teacher at my HS had them give me a wicked awesome discount on these (close to %50) and they were still over $200 a piece. I love these guys and they are probably about due for a calibration. Proto Slide Hammer: I wish I had gotten the kit with all the different heads, but this was all that was in stock. I love this tool. It ran me about $120. Box of Soapstone Stanley Tape Measures: On clearance at lowes for $11 a set. I love these guys. Not having a tape measure is not an option. Welding Helmet Lenses Crane Cams Crankshaft Socket: Use this to degree cams on limited FE motors. Blower Irwin 76 Piece Tap&Die Set: Got this off amazon for around $100. It's a nice set for the money. I just wish it had some bigger taps. Right Side Drawers: Top Drawer: Misc Scissors: For cutting. Project Source 6-in-1: Garbage screwdriver that I can't complain about because it was about two bucks 88 Cent Project Source Screwdrivers: Make great small prybars. I'm not about to break my Kleins. Lincoln Electric Lug Crimper: About $15 for crimping all sorts of lugs. Everlast Steering Wheel Puller: About $15 for pulling off Harmonic Balancers Performance Tool? Pitman Arm Puller: Got on sale off Jegs for pulling pitman arms Lenox 8-in-1 Screwdriver: I bought this for about $8 because I'm a Lenox fan. It is now in my tool belt. Summit Racing Wire Stripper/Crimper: Came with a box of spark plug terminals. About what you'd expect out of a free tool. Something or the other brand Ring Compressor: The corrugated style makes it easier to keep the tool from slipping into the bore with the piston. Crescent 6-in1 Screwdriver: Is now a nutdriver. Innova Timing Light: I got this off of Jegs or Summit for about $80. It isn't the best one on the market, but it is really nice Kobalt Adjustable Wrench: Garbage. PowerTorque Box end Wrenches: These are pretty good for $20 a set. Stanley Wrenches: These are sold at lowes for about twelve bucks a set. They are decent wrenches for the price and you can never have too many sets. Fuller Claw Hammer: I got this used as a gift when I was 5 or 6, It's a nice hammer that I used when working with my dad. It only sees occasional use now that the grip is gone. Zip Ties: Because zip ties are what holds the world together Performance Tool Valve Spring Compressor: This is an older style that you have to take the heads off for. It was about $30. I'm not a professional so I can't say anything, other than it works. Sunex Sockets and M12 Lantern: Already covered these elsewhere. Milwaukee M12 Inspection Camera: Great entry level inspection camera. $200 at HD. Left Hand Drawers: Irwin Vise-Grips and C-Clamp: You can never have enough clamps or vise-grips. MightyVac Hand Vacuum Pump: This is geared towards bleeding brakes so I picked it up on sale at Napa for about $35. Seems to be acceptable. Stanley Hand Plane: This is a tool that doesn't see much action anymore. I need to get back into woodworking. Astro Tool Trim Removal Set: Grabbed this on Amazon for about $20 on sale. It has a really high quality tool roll and always gets the job done. Imperial Brake Tubing Bender: I've used worse and it was only $45. Gearwrench Ratcheting Wrench Set: You can never have too many wrenches. I picked this up for a smokin deal of $50 thanks to Jimbo. Dewalt Corded Drill: This thing is only $100 and was purchased before my cordless days. It will hold its own. Makita Variable Speed Buffer/Polisher/Sander: Costs $200. I bought this after using one at work polishing stainless piping and tanks for about a week straight. Extremely impressive machine. 1 Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 2, 2016 Author Report Share Posted March 2, 2016 Only four more episodes left. Quote Link to comment Share on other sites More sharing options...
JimboS1ice Posted March 2, 2016 Report Share Posted March 2, 2016 1 hour ago, Stercorarius said: Only four more episodes left. You've inspired me bro, I did it on my two easier set ups but Im not touching my cluster you know what box full of hammers, pliers, screw drivers, putty knives, you name it its in there. 1 Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 2, 2016 Author Report Share Posted March 2, 2016 You've inspired me bro, I did it on my two easier set ups but Im not touching my cluster you know what box full of hammers, pliers, screw drivers, putty knives, you name it its in there. Awesome man! I was hoping I'd get to see some threads to read through of other people's tools. I'm going to look through your thread as soon as I get off work. Quote Link to comment Share on other sites More sharing options...
JimboS1ice Posted March 2, 2016 Report Share Posted March 2, 2016 Awesome man! I was hoping I'd get to see some threads to read through of other people's tools. I'm going to look through your thread as soon as I get off work. Until I buy a house with a garage my tool space is limited and quickly out grew what I should have for the space lol so it's just tools everywhere here and there lol Jimbo Sent from my iPhone using Tapatalk 2 Quote Link to comment Share on other sites More sharing options...
KnarlyCarl Posted March 2, 2016 Report Share Posted March 2, 2016 Awesome man! I was hoping I'd get to see some threads to read through of other people's tools. I'm going to look through your thread as soon as I get off work. You're on dude! But I don't do mechanic work so not going to have the volume you have Sent from my SCH-I535 using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 2, 2016 Author Report Share Posted March 2, 2016 You're on dude! But I don't do mechanic work so not going to have the volume you have Sent from my SCH-I535 using Tapatalk I love seeing plumbing tools. Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 3, 2016 Author Report Share Posted March 3, 2016 Episode 11: Screw It All Today I'm going to cover my accessory bags. Got a satchel of some batteries here. Something along the lines of 2 2Ah, 2 4Ah, and 2 5Ah Dewalt 20v's and 1 4Ah, and 6 2Ah M12's Bits and Pieces: Irwin SpeedBore Spade-Bit Set: These aren't as nice as the self-feeding Boschs, but they still work really well and only cost $20 and come with this awesome case. Skil Drill Bit Index: $20 garbage that can't be used on metal. DeWalt Gold Oxide Bit Set: These only run about $12 and work okay, but they dull about as quickly as you would expect a $12 set of bits too. DeWalt Black Oxide Bit Set: Not sure what the difference is from the gold ones. Haven't used these a whole lot. DeWalt Organizer: These things are like $5 and are a great way to keep your stuff from floating around in the bottom of your bag. Lenox Hole Saws: Not the cheapest, but I believe that these are the best hole saws on the market. Greenlee Step Bit: This thing ran about $60 which is typical for a decent step bit. It performs well. Black and Decker Hole Saw: Meh Bosch Hammer Drill Bits: Great bits for cheap, but it doesn't have as much variety as I would like. I don't drill a lot of concrete. DeWalt Torque-Flex Bit Set: Like $15 and they are some nice bits. The nut driver magnets come out really quickly though. I have broken a few tips of these. DeWalt Bit Set: Decent Cheap Bits. Misc. Bits DeWalt Organizer Some grinder stuff Welding rod tubes make great sawzall blade keepers. Lenox Blades: I will maintain that these are the best blades on the market untill I am shown otherwise. Milwaukee Blades: Team red also makes some really nice blades. Bosch Blades: Haven't seen much use, but they seem alright. Dewalt Blades: Haven't seen much use. 2 Quote Link to comment Share on other sites More sharing options...
KnarlyCarl Posted March 3, 2016 Report Share Posted March 3, 2016 Man oh man it just keeps coming! Once you get your project vehicle up and running, you putting all this in it? I agree with your statement on the lenox hole saws, but for wood cutting with the fuel sawzall, the Milwaukee blade, now labelled "the Ax" is my absolute favorite. It has that starting "hook" on the end that makes it a breeze starting a plunge cut Sent from my SCH-I535 using Tapatalk Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 3, 2016 Author Report Share Posted March 3, 2016 Man oh man it just keeps coming! Once you get your project vehicle up and running, you putting all this in it? I agree with your statement on the lenox hole saws, but for wood cutting with the fuel sawzall, the Milwaukee blade, now labelled "the Ax" is my absolute favorite. It has that starting "hook" on the end that makes it a breeze starting a plunge cut Sent from my SCH-I535 using Tapatalk I'm not sure yet. I'd have to build some legit toolboxes first. It's had some progress since this pic, but nothing dramatic. I want to have the motor in by the end of the month. I don't know how to get it in because I lifted it out by hand with my brother but it'll take a boom to go back in. Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 3, 2016 Author Report Share Posted March 3, 2016 Episode 12: Insert Porno-Sounding Title Here Today I've got another tool bag for y'all. Kobalt Pliers and That Other Thing Kobalt Pliers: All my pliers have come from the same $30-$40 set, so they have price going for them. They aren't the greatest and are all fairly bulky, but they are plenty enough for homeowners or the occasional user. That other thing: Irwin Marple High Impact Chisel: I'm not sure what it is with chisels and clear plastic, but I don't like my stuff being see through. Other than that, what little use these have had has given me a very positive impression of them. FatMax Bulldog Snips: These don't see as much use as the other snips, but they are really nice. Milwaukee Aviation Snips: I paid way too much buying these individually, like $15 a piece, and they went on sale for $30 for the set at some point. These are really awesome snips and have become my go to for cutting automotive patch panels. The offset is really nice. The only thing that I should note is that the mechanism for locking them closed comes open if any pressure is applied on the handles. This could be good or bad. It is nice when you want them to open, but sucks if you want to put them in your pocket. Pittsburgh Screwdrivers: The rest of the $9 set. They are alright. Kobalt Pass-Through Socket Sets: These guys were on clearance for less than $10 a kit and I just was too curious about pass through sockets to pass them up. I'm glad I didn't buy the expensive craftsman set like I was planning to, because these see extremely rare use. I really just use the adapters these sockets come with and use them as universal spline sockets. The ratchets in these things are complete crap. If you put pressure on them the right way, they rotate freely in both directions.Oh well, is what it is. Husky Bit Socket Set: These run $25 at HD. These were purchased because I needed allen key sockets, and this was an affordable option and came with other bits for the price of a set of just the allen key sockets. They come with a lifetime guarantee and seem pretty nice so far. I'm not using these everyday so they suit my needs. Husky File Set: These are a $10 set so I bought them because I needed files. These are by no means high quality files. The handles are nearly worthless. That being said, they do work for my usage levels. Milwaukee Document Bag: You saw these holding my T-handle allen keys and now another one is holding my files. These guys are expensive, but they are beyond useful for holding small tool sets like these. I also have a third one for my reimbursable receipts. 1 Quote Link to comment Share on other sites More sharing options...
JimboS1ice Posted March 3, 2016 Report Share Posted March 3, 2016 My Irwin chisels are still in the package, I like that little husky kit might have to invest in one of them. Best is your "plier wrench" although it's not knipex design it's still (cough cough) innovative. Jimbo Sent from my iPhone using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 4, 2016 Author Report Share Posted March 4, 2016 Episode 13: The Wallflowers These guys hang out in the background. Lunati Degree Wheel: Evercraft Creeper Cart: Finally bought one of these a while back for about $80. It really is one of the better creepers that I have used. Irwin Magnetic Box Beam Level: I love irwin and this is one fabulous level, but I wouldn't have bought it if I had known the price before I got to the register. It was $110. I needed a magnetic level for some steel I-beams and should have gotten something cheaper. Oh well. Phase II Dial Indicator and Magnetic Stand: OEM Tool Snap Ring Pliers: Complete garbage. Life is too short to spend time using crappy snap ring pliers. Napa Grease Gun: ProGrade Bar Clamps: These actually work fairly well so far. They have only been used to glue together a few MDF sub enclosures. I don't remember a price on these, but they were pretty cheap. No Name Hacksaw Kobalt Caulk Gun Craftsman 19.2V Tools: I got these as a gift several years back and the battery charger and battery were toast almost immediately. I haven't used them since, but I would like to buy a battery and charger for them and at least get the vacuum back up and running. I may also just do a giveaway. I really don't know. 1 Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 4, 2016 Author Report Share Posted March 4, 2016 Episode 14: The Ones That Got Away This is the final installment in the series. Hi-Lift Jack: This is about $80 and I use it occasionally for working on my pickup and changing gearboxes/wheels on irrigation pivots. Be careful with these widow makers. WHAT'S IN THE BOX?!? No joke, I got this toolbox when I was about 3 years old. I don't think that it is a real tool box, I believe it may have come with a toy tool set. I don't remember. I just remember hauling it around as a child trying to "fix" things. It still sees regular and frequent use. Contents: At the time I took the photos these were all inside the box, some have since migrated to my toolbelt. Irwin Tape: Nice tape. Not having a tape is not an option. TuffENuf Tape: I don't know where it came from, but it is better than nothing. Milwaukee Tape: It came free from IHLCanada and I am pleasantly surprised with it's quality. Irwin Chalk Line: It has been working very well for me. I don't like the blue chalk though. Dewalt Tape: Great tape that I picked up for large layout work. Bernzomatic MAP Gas Torch: It gets things hot. Duracell 1300 Lumen Flashlight: It only runs about $20 at Costco and is really really bright. M12 Bluetooth Speaker: I bought this thing as a bare tool to run in equipment without radios. It works satisfactorily. Central Machinery Wood Lathe with Nova Chuck: Not the greatest lathe with the greatest chuck. I have a couple finished bowls somewhere.... Chicago Electric Chainsaw: This was a gift and so I shouldn't say anything, but any other brand is better and this thing is complete crap. Dremel Trio and 4000 The dremel is great and is being phased out by my M12 rotary tool. The Dremel trio is really just a router with proprietary overpriced attachments. Windsor Design Chisel and Gouge Set: Not recommended for frequent use. Black and Decker Jigsaw: It isn't a fine wood working implement, but it gets the job done. Dremel Engraver: For only $25 this thing is worth investing in to make sure your tools stay yours. Great little guy. M12 Rotary Tool and Ratchet: I haven't gotten a lot of use out of the rotary tool yet, but my impressions are very positive. I have gotten a ton of use out of the ratchet and love the little guy for assembling and disassembling parts that aren't too tight on cars. I used my coworkers for a while when running steel cable overhead and purchased one the next day. This was my first M12 purchase. I got the kit for around $160. 2 Quote Link to comment Share on other sites More sharing options...
Stercorarius Posted March 4, 2016 Author Report Share Posted March 4, 2016 1 Quote Link to comment Share on other sites More sharing options...
77Ford01 Posted March 4, 2016 Report Share Posted March 4, 2016 Thanks for the entertainment ......I plan on watching again [emoji851] DeWalt 1 Quote Link to comment Share on other sites More sharing options...
JimboS1ice Posted March 4, 2016 Report Share Posted March 4, 2016 Nice dude thanks for posting I've enjoyed checking out your set up. Jimbo Sent from my iPad using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.